HylaFAX не кладет трубку - Компьютерный форум OSzone.net

Доброго времени суток. Беда такая: после приема 5-10 (а иногда и на много больше) факсов прием данных обрывается и сервер тупа держит трубку поднятой. Помогает только перезагрузка. Факс используется только на прием. Пробывал играть скоростями, но это не помогло, менял модем тоже не помогло. HylaFAX 6.0.3 ubuntu 10.04 В логе вот что:

Код:

Mar 21 17:10:25.28: [  887]: SESSION BEGIN 000000759 19995551212

Mar 21 17:10:25.28: [  887]: HylaFAX (tm) Version 6.0.3

Mar 21 17:10:25.28: [  887]: MODEM set XON/XOFF/FLUSH: input ignored, output disabled

Mar 21 17:10:25.28: [  887]: <-- [13:AT+FCLASS=1A\r]

Mar 21 17:10:30.46: [  887]: --> [7:CONNECT]

Mar 21 17:10:30.46: [  887]: ANSWER: FAX CONNECTION  DEVICE '/dev/ttyS3'

Mar 21 17:10:30.46: [  887]: STATE CHANGE: ANSWERING -> RECEIVING

Mar 21 17:10:30.46: [  887]: RECV FAX: begin

Mar 21 17:10:30.46: [  887]: <-- HDLC<32:FF C0 04 B5 00 AA 12 9E 36 86 62 82 1A 04 14 2E B6 94 04 6A A6 4E CE 96 F6 76 04 6C 74 0C 74 CC>

Mar 21 17:10:30.46: [  887]: <-- data [32]

Mar 21 17:10:30.46: [  887]: <-- data [2]

Mar 21 17:10:30.63: [  887]: --> [7:CONNECT]

Mar 21 17:10:30.63: [  887]: <-- HDLC<23:FF C0 02 CA 22 4A 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04>

Mar 21 17:10:30.63: [  887]: <-- data [23]

Mar 21 17:10:30.63: [  887]: <-- data [2]

Mar 21 17:10:31.35: [  887]: --> [7:CONNECT]

Mar 21 17:10:31.35: [  887]: <-- HDLC<13:FF C8 01 00 77 5F 23 01 FB C1 01 01 18>

Mar 21 17:10:31.35: [  887]: <-- data [13]

Mar 21 17:10:31.35: [  887]: <-- data [2]

Mar 21 17:10:33.61: [  887]: --> [2:OK]

Mar 21 17:10:33.61: [  887]: <-- [9:AT+FRH=3\r]

Mar 21 17:10:40.61: [  887]: --> [0:]

Mar 21 17:10:40.61: [  887]: MODEM <Empty line>

Mar 21 17:10:40.61: [  887]: MODEM TIMEOUT: waiting for v.21 carrier

Mar 21 17:10:40.61: [  887]: <-- data [1]

Mar 21 17:10:40.62: [  887]: --> [2:OK]

Mar 21 17:10:40.62: [  887]: DELAY 70 ms

Mar 21 17:10:40.69: [  887]: <-- [9:AT+FTH=3\r]

Mar 21 17:10:40.72: [  887]: --> [7:CONNECT]

Mar 21 17:10:40.72: [  887]: <-- HDLC<32:FF C0 04 B5 00 AA 12 9E 36 86 62 82 1A 04 14 2E B6 94 04 6A A6 4E CE 96 F6 76 04 6C 74 0C 74 CC>

Mar 21 17:10:40.72: [  887]: <-- data [32]

Mar 21 17:10:40.72: [  887]: <-- data [2]

Mar 21 17:10:40.89: [  887]: --> [7:CONNECT]

Mar 21 17:10:40.89: [  887]: <-- HDLC<23:FF C0 02 CA 22 4A 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04>

Mar 21 17:10:40.89: [  887]: <-- data [23]

Mar 21 17:10:40.89: [  887]: <-- data [2]

Mar 21 17:10:41.61: [  887]: --> [7:CONNECT]

Mar 21 17:10:41.61: [  887]: <-- HDLC<13:FF C8 01 00 77 5F 23 01 FB C1 01 01 18>

Mar 21 17:10:41.61: [  887]: <-- data [13]

Mar 21 17:10:41.61: [  887]: <-- data [2]

Mar 21 17:10:43.87: [  887]: --> [2:OK]

Mar 21 17:10:43.87: [  887]: <-- [9:AT+FRH=3\r]

Mar 21 17:10:45.89: [  887]: --> [7:CONNECT]

Mar 21 17:10:47.50: [  887]: --> HDLC<25:FF C0 C2 6C 4C 1C 9C AC 2C 04 04 04 04 04 04 04 04 04 04 04 04 04 04 81 69>

Mar 21 17:10:47.51: [  887]: --> [2:OK]

Mar 21 17:10:47.51: [  887]: RECV recv TSI (sender id)

Mar 21 17:10:47.51: [  887]: REMOTE TSI "459826"

Mar 21 17:10:47.51: [  887]: <-- [9:AT+FRH=3\r]

Mar 21 17:10:47.52: [  887]: --> [7:CONNECT]

Mar 21 17:10:47.82: [  887]: --> HDLC<9:FF C8 C1 00 60 1F 00 09 FD>

Mar 21 17:10:47.82: [  887]: --> [2:OK]

Mar 21 17:10:47.82: [  887]: RECV recv DCS (command signal)

Mar 21 17:10:47.83: [  887]: REMOTE wants 9600 bit/s

Mar 21 17:10:47.83: [  887]: REMOTE wants A4 page width (215 mm)

Mar 21 17:10:47.83: [  887]: REMOTE wants unlimited page length

Mar 21 17:10:47.83: [  887]: REMOTE wants 3.85 line/mm

Mar 21 17:10:47.83: [  887]: REMOTE wants 1-D MH

Mar 21 17:10:47.83: [  887]: RECV training at v.29 9600 bit/s

Mar 21 17:10:47.83: [  887]: MODEM set XON/XOFF/DRAIN: input ignored, output generated

Mar 21 17:10:47.83: [  887]: <-- [10:AT+FRM=96\r]

Mar 21 17:10:48.51: [  887]: --> [7:CONNECT]

Mar 21 17:10:50.14: [  887]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled

Mar 21 17:10:50.14: [  887]: RECV: TCF 1953 bytes, 5% non-zero, 1843 zero-run

Mar 21 17:10:50.14: [  887]: --> [10:NO CARRIER]

Mar 21 17:10:50.14: [  887]: DELAY 70 ms

Mar 21 17:10:50.22: [  887]: TRAINING succeeded

Mar 21 17:10:50.22: [  887]: <-- [9:AT+FTH=3\r]

Mar 21 17:10:50.41: [  887]: --> [7:CONNECT]

Mar 21 17:10:50.41: [  887]: <-- HDLC<3:FF C8 21>

Mar 21 17:10:50.41: [  887]: <-- data [3]

Mar 21 17:10:50.41: [  887]: <-- data [2]

Mar 21 17:10:51.58: [  887]: --> [2:OK]

Mar 21 17:10:51.59: [  887]: <-- [10:AT+FRM=96\r]

Mar 21 17:10:55.87: [  887]: --> [7:CONNECT]

Mar 21 17:10:55.87: [  887]: MODEM input buffering enabled

Mar 21 17:10:55.87: [  887]: MODEM set XON/XOFF/FLUSH: input ignored, output generated

Mar 21 17:10:55.87: [  887]: RECV: begin page

Mar 21 17:10:57.49: [  887]: RECV/CQ: Bad 1D pixel count, row 0, got 1942, expected 1728

В системном логе:

Код:

root@FAX:/var/log# cat syslog.1 | grep "Mar 21 17:10"

Mar 21 17:10:30 FAX FaxGetty[887]: ANSWER: FAX CONNECTION  DEVICE '/dev/ttyS3'

Mar 21 17:10:57 FAX kernel: [ 6225.816040] __ratelimit: 9 callbacks suppressed

Mar 21 17:10:57 FAX kernel: [ 6225.816046] faxgetty[887]: segfault at 73736ba8 ip 0805c083 sp bfc0ed90 error 4 in faxgetty[8048000+72000]

Конфиг программы:

Код:

CountryCode:                10

AreaCode:                423

FAXNumber:                +1.999.555.1212

LongDistancePrefix:        1

InternationalPrefix:        011

DialStringRules:        etc/dialrules

ServerTracing:                1

SessionTracing:                0xFFF

RecvFileMode:                0644

LogFileMode:                0644

DeviceMode:                0644

RingsBeforeAnswer:        1

SpeakerVolume:                off

GettyArgs:                "-h %l dx_%s"

LocalIdentifier:        XXX

TagLineFont:                etc/lutRS18.pcf

TagLineFormat:                "From %%l|%c|Page %%P of %%T"

MaxRecvPages:                25

#

#

# Modem-related stuff: should reflect modem command interface

# and hardware connection/cabling (e.g. flow control).

#

ModemType:                Class1                # use class 1 interface

ModemRate:                19200                # rate for DCE-DTE communication

ModemFlowControl:        xonxoff                # software flow control

#

ModemSetupDTRCmd:        ATS13=1&D2        # setup so DTR drop resets modem

ModemSetupDCDCmd:        AT&C1                # setup so DCD reflects carrier (or not)

ModemNoFlowCmd:                AT&H0&I0&R1        # setup modem for no flow control

ModemHardFlowCmd:        AT&H1&I0&R2        # setup modem for hardware flow control

ModemSoftFlowCmd:        AT&H2&I2&R1        # setup modem for software flow control

ModemResultCodesCmd:        ATQ0X4                # enable result codes

#

ModemMfrQueryCmd:        !USR

ModemModelQueryCmd:        ATI3

ModemRevQueryCmd:        ATI7                # XXX returns a multi-line result

#

# When AT+FCLASS=1 is issued the modem automatically switches

# to software flow control; these parameters let the fax software

# reset flow control as needed after entering Class 1.

#

Class1NFLOCmd:                AT&H0&I0&R1        # setup modem for no flow control

Class1HFLOCmd:                AT&H1&I0&R2        # setup modem for hardware flow control

Class1SFLOCmd:                ""                # modem does this automatically

#

# This should resolve "DIS/DTC received 3 times" errors:

#

Class1ResponseWaitCmd:        AT+FRS=1        # wait after sending TCF for response

#

# The remainder of this configuration is included so that the

# modem "idles" in Class 0 while not sending or receiving facsimile.

#

ModemSetupAACmd:        AT+FCLASS=0        # leave modem idling in class 0

ModemAnswerCmd:                AT+FCLASS=1A        # answer in Class 1

#

# When using AT+FRS=n we see USR modems reset themselves in the middle of sessions

# this is not good.  So, we seem to work-around that problem by not using the

# command.  Unfortunately, this isn't an ideal thing.

#

Class1SwitchingCmd:        "<delay\0727>"

Помоги, кто знает, а то уже не знаю что и делать....