Debian/Ubuntu - HylaFAX не кладет трубку

Debian/Ubuntu - HylaFAX не кладет трубку

Zoldan

Новый участник

Сообщения: 22
Благодарности: 0

Доброго времени суток. Беда такая: после приема 5-10 (а иногда и на много больше) факсов прием данных обрывается и сервер тупа держит трубку поднятой. Помогает только перезагрузка. Факс используется только на прием. Пробывал играть скоростями, но это не помогло, менял модем тоже не помогло. HylaFAX 6.0.3 ubuntu 10.04 В логе вот что:

Код:

Mar 21 17:10:25.28: [  887]: SESSION BEGIN 000000759 19995551212
Mar 21 17:10:25.28: [  887]: HylaFAX (tm) Version 6.0.3
Mar 21 17:10:25.28: [  887]: MODEM set XON/XOFF/FLUSH: input ignored, output disabled
Mar 21 17:10:25.28: [  887]: <-- [13:AT+FCLASS=1A\r]
Mar 21 17:10:30.46: [  887]: --> [7:CONNECT]
Mar 21 17:10:30.46: [  887]: ANSWER: FAX CONNECTION  DEVICE '/dev/ttyS3'
Mar 21 17:10:30.46: [  887]: STATE CHANGE: ANSWERING -> RECEIVING
Mar 21 17:10:30.46: [  887]: RECV FAX: begin
Mar 21 17:10:30.46: [  887]: <-- HDLC<32:FF C0 04 B5 00 AA 12 9E 36 86 62 82 1A 04 14 2E B6 94 04 6A A6 4E CE 96 F6 76 04 6C 74 0C 74 CC>
Mar 21 17:10:30.46: [  887]: <-- data [32]
Mar 21 17:10:30.46: [  887]: <-- data [2]
Mar 21 17:10:30.63: [  887]: --> [7:CONNECT]
Mar 21 17:10:30.63: [  887]: <-- HDLC<23:FF C0 02 CA 22 4A 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04>
Mar 21 17:10:30.63: [  887]: <-- data [23]
Mar 21 17:10:30.63: [  887]: <-- data [2]
Mar 21 17:10:31.35: [  887]: --> [7:CONNECT]
Mar 21 17:10:31.35: [  887]: <-- HDLC<13:FF C8 01 00 77 5F 23 01 FB C1 01 01 18>
Mar 21 17:10:31.35: [  887]: <-- data [13]
Mar 21 17:10:31.35: [  887]: <-- data [2]
Mar 21 17:10:33.61: [  887]: --> [2:OK]
Mar 21 17:10:33.61: [  887]: <-- [9:AT+FRH=3\r]
Mar 21 17:10:40.61: [  887]: --> [0:]
Mar 21 17:10:40.61: [  887]: MODEM <Empty line>
Mar 21 17:10:40.61: [  887]: MODEM TIMEOUT: waiting for v.21 carrier
Mar 21 17:10:40.61: [  887]: <-- data [1]
Mar 21 17:10:40.62: [  887]: --> [2:OK]
Mar 21 17:10:40.62: [  887]: DELAY 70 ms
Mar 21 17:10:40.69: [  887]: <-- [9:AT+FTH=3\r]
Mar 21 17:10:40.72: [  887]: --> [7:CONNECT]
Mar 21 17:10:40.72: [  887]: <-- HDLC<32:FF C0 04 B5 00 AA 12 9E 36 86 62 82 1A 04 14 2E B6 94 04 6A A6 4E CE 96 F6 76 04 6C 74 0C 74 CC>
Mar 21 17:10:40.72: [  887]: <-- data [32]
Mar 21 17:10:40.72: [  887]: <-- data [2]
Mar 21 17:10:40.89: [  887]: --> [7:CONNECT]
Mar 21 17:10:40.89: [  887]: <-- HDLC<23:FF C0 02 CA 22 4A 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04>
Mar 21 17:10:40.89: [  887]: <-- data [23]
Mar 21 17:10:40.89: [  887]: <-- data [2]
Mar 21 17:10:41.61: [  887]: --> [7:CONNECT]
Mar 21 17:10:41.61: [  887]: <-- HDLC<13:FF C8 01 00 77 5F 23 01 FB C1 01 01 18>
Mar 21 17:10:41.61: [  887]: <-- data [13]
Mar 21 17:10:41.61: [  887]: <-- data [2]
Mar 21 17:10:43.87: [  887]: --> [2:OK]
Mar 21 17:10:43.87: [  887]: <-- [9:AT+FRH=3\r]
Mar 21 17:10:45.89: [  887]: --> [7:CONNECT]
Mar 21 17:10:47.50: [  887]: --> HDLC<25:FF C0 C2 6C 4C 1C 9C AC 2C 04 04 04 04 04 04 04 04 04 04 04 04 04 04 81 69>
Mar 21 17:10:47.51: [  887]: --> [2:OK]
Mar 21 17:10:47.51: [  887]: RECV recv TSI (sender id)
Mar 21 17:10:47.51: [  887]: REMOTE TSI "459826"
Mar 21 17:10:47.51: [  887]: <-- [9:AT+FRH=3\r]
Mar 21 17:10:47.52: [  887]: --> [7:CONNECT]
Mar 21 17:10:47.82: [  887]: --> HDLC<9:FF C8 C1 00 60 1F 00 09 FD>
Mar 21 17:10:47.82: [  887]: --> [2:OK]
Mar 21 17:10:47.82: [  887]: RECV recv DCS (command signal)
Mar 21 17:10:47.83: [  887]: REMOTE wants 9600 bit/s
Mar 21 17:10:47.83: [  887]: REMOTE wants A4 page width (215 mm)
Mar 21 17:10:47.83: [  887]: REMOTE wants unlimited page length
Mar 21 17:10:47.83: [  887]: REMOTE wants 3.85 line/mm
Mar 21 17:10:47.83: [  887]: REMOTE wants 1-D MH
Mar 21 17:10:47.83: [  887]: RECV training at v.29 9600 bit/s
Mar 21 17:10:47.83: [  887]: MODEM set XON/XOFF/DRAIN: input ignored, output generated
Mar 21 17:10:47.83: [  887]: <-- [10:AT+FRM=96\r]
Mar 21 17:10:48.51: [  887]: --> [7:CONNECT]
Mar 21 17:10:50.14: [  887]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled
Mar 21 17:10:50.14: [  887]: RECV: TCF 1953 bytes, 5% non-zero, 1843 zero-run
Mar 21 17:10:50.14: [  887]: --> [10:NO CARRIER]
Mar 21 17:10:50.14: [  887]: DELAY 70 ms
Mar 21 17:10:50.22: [  887]: TRAINING succeeded
Mar 21 17:10:50.22: [  887]: <-- [9:AT+FTH=3\r]
Mar 21 17:10:50.41: [  887]: --> [7:CONNECT]
Mar 21 17:10:50.41: [  887]: <-- HDLC<3:FF C8 21>
Mar 21 17:10:50.41: [  887]: <-- data [3]
Mar 21 17:10:50.41: [  887]: <-- data [2]
Mar 21 17:10:51.58: [  887]: --> [2:OK]
Mar 21 17:10:51.59: [  887]: <-- [10:AT+FRM=96\r]
Mar 21 17:10:55.87: [  887]: --> [7:CONNECT]
Mar 21 17:10:55.87: [  887]: MODEM input buffering enabled
Mar 21 17:10:55.87: [  887]: MODEM set XON/XOFF/FLUSH: input ignored, output generated
Mar 21 17:10:55.87: [  887]: RECV: begin page
Mar 21 17:10:57.49: [  887]: RECV/CQ: Bad 1D pixel count, row 0, got 1942, expected 1728

В системном логе:

Код:

root@FAX:/var/log# cat syslog.1 | grep "Mar 21 17:10"
Mar 21 17:10:30 FAX FaxGetty[887]: ANSWER: FAX CONNECTION  DEVICE '/dev/ttyS3'
Mar 21 17:10:57 FAX kernel: [ 6225.816040] __ratelimit: 9 callbacks suppressed
Mar 21 17:10:57 FAX kernel: [ 6225.816046] faxgetty[887]: segfault at 73736ba8 ip 0805c083 sp bfc0ed90 error 4 in faxgetty[8048000+72000]

Конфиг программы:

Код:

CountryCode:		10
AreaCode:		423
FAXNumber:		+1.999.555.1212
LongDistancePrefix:	1
InternationalPrefix:	011
DialStringRules:	etc/dialrules
ServerTracing:		1
SessionTracing:		0xFFF
RecvFileMode:		0644
LogFileMode:		0644
DeviceMode:		0644
RingsBeforeAnswer:	1
SpeakerVolume:		off
GettyArgs:		"-h %l dx_%s"
LocalIdentifier:	XXX
TagLineFont:		etc/lutRS18.pcf
TagLineFormat:		"From %%l|%c|Page %%P of %%T"
MaxRecvPages:		25
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:		Class1		# use class 1 interface
ModemRate:		19200		# rate for DCE-DTE communication
ModemFlowControl:	xonxoff		# software flow control
#
ModemSetupDTRCmd:	ATS13=1&D2	# setup so DTR drop resets modem
ModemSetupDCDCmd:	AT&C1		# setup so DCD reflects carrier (or not)
ModemNoFlowCmd:		AT&H0&I0&R1	# setup modem for no flow control
ModemHardFlowCmd:	AT&H1&I0&R2	# setup modem for hardware flow control
ModemSoftFlowCmd:	AT&H2&I2&R1	# setup modem for software flow control
ModemResultCodesCmd:	ATQ0X4		# enable result codes
#
ModemMfrQueryCmd:	!USR
ModemModelQueryCmd:	ATI3
ModemRevQueryCmd:	ATI7		# XXX returns a multi-line result
#
# When AT+FCLASS=1 is issued the modem automatically switches
# to software flow control; these parameters let the fax software
# reset flow control as needed after entering Class 1.
#
Class1NFLOCmd:		AT&H0&I0&R1	# setup modem for no flow control
Class1HFLOCmd:		AT&H1&I0&R2	# setup modem for hardware flow control
Class1SFLOCmd:		""		# modem does this automatically
#
# This should resolve "DIS/DTC received 3 times" errors:
#
Class1ResponseWaitCmd:	AT+FRS=1	# wait after sending TCF for response
#
# The remainder of this configuration is included so that the
# modem "idles" in Class 0 while not sending or receiving facsimile.
#
ModemSetupAACmd:	AT+FCLASS=0	# leave modem idling in class 0
ModemAnswerCmd:		AT+FCLASS=1A	# answer in Class 1
#
# When using AT+FRS=n we see USR modems reset themselves in the middle of sessions
# this is not good.  So, we seem to work-around that problem by not using the
# command.  Unfortunately, this isn't an ideal thing.
#
Class1SwitchingCmd:	"<delay\0727>"

Помоги, кто знает, а то уже не знаю что и делать....

Отправлено: 04:12, 26-03-2012

dvv-home

Новый участник

Сообщения: 1
Благодарности: 0

Профиль | Отправить PM | Цитировать

Когда у меня был Целерон 700 Мг /ОЗУ 512 модем внешний Курьер, то на дню до 3 раз мог трубку не ложить. Hylafax перегружал, потом надоело в крон перезагрузку засунул. Сейчас HP /ubuntu server 10.04/ 3-модема внешних и как часики

Отправлено: 13:58, 03-04-2012 | #2

Для отключения данного рекламного блока вам необходимо зарегистрироваться или войти с учетной записью социальной сети.

Если же вы забыли свой пароль на форуме, то воспользуйтесь данной ссылкой для восстановления пароля.