Проблема такова
Есть внешний HDD (A-data) уже около 2-х лет, бывало тупил, но лечился чекдиском и все продолжало нормально работать до недавнего времени...
В общем перестал копировать на него (виснит и все) - чек уже не помог...решил форматнуть, но не вышло выдавал ошибку что мол не может.
Думал может контроллер или еще что тупит...вытащил seagate и подцепил к ПК, пробовал все выше перечисленное результат все тот же...
Пробовал сканировать викторией через Win - вроде бэдов не было.
Прошу помощи...
прилагаю SMART smartctl 5.41 2011-06-09 r3365 [i686-linux-3.0.4-pmagic] до скана виктории
читать дальше »
Код:
smartctl 5.41 2011-06-09 r3365 [i686-linux-3.0.4-pmagic] (local build)
Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net
=== START OF INFORMATION SECTION ===
Model Family: Seagate Momentus 5400.6
Device Model: ST9500325AS
Serial Number: 6VEPHLFT
LU WWN Device Id: 5 000c50 036820603
Firmware Version: 0001SDM1
User Capacity: 500,107,862,016 bytes [500 GB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: 8
ATA Standard is: ATA-8-ACS revision 4
Local Time is: Wed Mar 6 10:47:37 2013 UTC
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 0) seconds.
Offline data collection
capabilities: (0x73) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
No Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 135) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x103b) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 117 099 006 Pre-fail Always - 124833274
3 Spin_Up_Time 0x0003 099 098 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 099 099 020 Old_age Always - 1765
5 Reallocated_Sector_Ct 0x0033 067 067 036 Pre-fail Always - 679
7 Seek_Error_Rate 0x000f 065 060 030 Pre-fail Always - 3171989
9 Power_On_Hours 0x0032 099 099 000 Old_age Always - 1202
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 870
184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0
187 Reported_Uncorrect 0x0032 099 099 000 Old_age Always - 1
188 Command_Timeout 0x0032 099 099 000 Old_age Always - 60130459663
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 072 048 045 Old_age Always - 28 (Min/Max 26/28)
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 1
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 225
193 Load_Cycle_Count 0x0032 097 097 000 Old_age Always - 7276
194 Temperature_Celsius 0x0022 028 052 000 Old_age Always - 28 (0 19 0 0)
195 Hardware_ECC_Recovered 0x001a 047 043 000 Old_age Always - 124833274
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
254 Free_Fall_Sensor 0x0032 100 100 000 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 12 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 12 occurred at disk power-on lifetime: 1196 hours (49 days + 20 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 71 03 80 01 32 40 Device Fault; Error: ABRT 3 sectors at LBA = 0x00320180 = 3277184
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 03 01 01 00 00 00 00 00:01:17.319 READ DMA EXT
00 00 00 00 00 00 00 04 00:01:17.096 NOP [Abort queued commands]
25 03 01 01 00 00 00 00 00:01:17.088 READ DMA EXT
00 00 00 00 00 00 00 04 00:01:17.015 NOP [Abort queued commands]
25 03 01 01 00 00 00 00 00:01:17.007 READ DMA EXT
Error 11 occurred at disk power-on lifetime: 1196 hours (49 days + 20 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 71 03 80 01 32 40 Device Fault; Error: ABRT 3 sectors at LBA = 0x00320180 = 3277184
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 03 01 01 00 00 00 00 00:01:17.088 READ DMA EXT
00 00 00 00 00 00 00 04 00:01:17.015 NOP [Abort queued commands]
25 03 01 01 00 00 00 00 00:01:17.007 READ DMA EXT
00 00 00 00 00 00 00 04 00:01:15.986 NOP [Abort queued commands]
00 00 00 00 00 00 00 04 00:01:02.338 NOP [Abort queued commands]
Error 10 occurred at disk power-on lifetime: 1196 hours (49 days + 20 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 71 03 80 01 32 40 Device Fault; Error: ABRT 3 sectors at LBA = 0x00320180 = 3277184
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 03 01 01 00 00 00 00 00:01:17.007 READ DMA EXT
00 00 00 00 00 00 00 04 00:01:15.986 NOP [Abort queued commands]
00 00 00 00 00 00 00 04 00:01:02.338 NOP [Abort queued commands]
00 00 00 00 00 00 00 04 00:00:48.751 NOP [Abort queued commands]
25 03 80 b7 b3 5f 40 02 00:00:37.520 READ DMA EXT
Error 9 occurred at disk power-on lifetime: 1177 hours (49 days + 1 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 71 03 80 01 32 40
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
e5 00 00 00 00 00 40 00 01:05:14.349 CHECK POWER MODE
00 00 00 00 00 00 00 04 01:04:08.049 NOP [Abort queued commands]
00 00 00 00 00 00 00 04 01:03:42.962 NOP [Abort queued commands]
25 03 08 5f 89 60 40 02 01:03:33.298 READ DMA EXT
35 03 80 c7 1e 9c 4e 02 01:03:33.199 WRITE DMA EXT
Error 8 occurred at disk power-on lifetime: 1176 hours (49 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 51 00 1c bb 5f 00
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
e7 00 00 00 00 00 40 00 00:03:04.803 FLUSH CACHE
e5 03 01 01 00 00 00 00 00:03:04.803 CHECK POWER MODE
00 00 00 00 00 00 00 04 00:03:03.245 NOP [Abort queued commands]
25 03 01 01 00 00 00 00 00:03:03.237 READ DMA EXT
00 00 00 00 00 00 00 04 00:03:03.222 NOP [Abort queued commands]
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
и после SMART виктории
читать дальше »
Код:
-------------------------------------------------------------------------
ID Name Value Worst Tresh Raw Health
-------------------------------------------------------------------------
1 Raw read error rate 114 99 6 69579076 •••••
3 Spin-up time 99 98 0 0 ••••
4 Number of spin-up times 99 99 20 1770 ••••
5 Reallocated sector count 61 61 36 804 •••
7 Seek error rate 65 60 30 3213443 •••
9 Power-on time 99 99 0 1226 ••••
10 Spin-up retries 100 100 97 0 •••••
12 Start/stop count 100 100 20 875 •••••
184 End-to-End error 100 100 99 0 •••••
187 Reported UNC error 99 99 0 1 ••••
188 Command timeout 99 94 0 68720721954 ••••
189 High Fly writes 100 100 0 0 •••••
190 Airflow temperature 67 48 45 33°C/91°F ••••
191 G-SENSOR shock counter 100 100 0 1 •••••
192 Power-off retract count 100 100 0 227 •••••
193 Load/unload cycle count 97 97 0 7363 ••••
194 HDA Temperature 33 52 0 33°C/91°F ••••
194 Minimum temperature 90 52 0 19°C/66°F -
195 Hardware ECC recovered 45 43 0 69579076 ••
197 Current pending sectors 100 100 0 0 •••••
198 Offline scan UNC sectors 100 100 0 0 •••••
199 Ultra DMA CRC errors 200 200 0 0 •••••
254 G-SENSOR shock counter 100 100 0 0 •••••
