[vadblm]

Что делать?????????????????7 »

Бэкапить данные и менять диск. Волшебных утилит для восстановления "плохих секторов" не существует, а те что так себя позиционируют - надувательство.
Также стоит выяснить, почему диск посыпался, чтобы с новым не случилась такая же история.
Cо SMART отчётом диска отправляйтесь в эту ветку.

[Flashbag]

Та я то дание забекапил )))
Жаль касу давать на новий, тепер лето ))))))))))

Так что совсем никак???

[vadblm]

Точный ответ можно дать только взглянув на SMART отчёт.
Если вы ещё диск не выкинули, пардон что долго не отвечал, то дайте вывод sudo smartctl -a /dev/sda сюда.
Если умирающий диск не sda, то подставьте нужную девноду. Посмотреть их можно командой sudo fdisk -l
Если smartmontools не установлен, то установите sudo apt-get install smartmontools

[DVDshnik]

HDDRegenerator'ом попробуйте диск прошерстить. Вдруг, да поможет.
При запуске программы отмечено, что дефекты исправляются на любых ОС и независимо от файловой системы.
Возможно, автор и лукавит, но мне данная программа позволила подлечить не один десяток жёстких дисков.

[vadblm]

Возможно, автор и лукавит »

То-то и оно, что лукавит. Но попытка не пытка, однако лучше не парясь нести менять по гарантии, ибо случай самый что ни на есть гарантийный - насколько я знаю palimpsest, он попусту не орёт.
Если она есть, эта гарантия

[Flashbag]

HDD Regenerator нифига не сделал, после запуска востановления плохих секторов он проверял сектори с бешеной и при чем постоянной скоростю, как часи, когда проверил первий первинний раздел показал что типа есть плохой сектор и давай его востановлять и....... BSoD....и винда улетела )))))

А диск я еще не викинул - удалил все раздели, установил на весь диск ubuntu-10.04 и радуюсь

Вообщем то проблема со скоростю чтения/записи:

-когда качаю что-то то никаких ошибок не происходит
-смотрю фильм - тоже все ок

-но когда начинають копировать большие файли (>=300mb) то пару сек. диск начинает цокать как бомба замедленного действия и система (ubuntu) зависает, потом отвисает и с любой операцией записи или чтения на диск - ошибка

input/output error
Readonly file system!


А на винде в таком случае сразу BSoD )))

[DVDshnik]

HDD Regenerator нифига не сделал....... BSoD....и винда улетела )

"Винда" тут при чём? Вовсе не нужна она.
Программулина запускается и работает с LiveCD диска.

[Flashbag]

З LiveCD WIndowza???
А можно проcто с загрузочной флешки ms-dos??????

[Flashbag]

Ну вот доигрался. Диск уже начинает цокать через 5 минут после загрузки.
Теперь сиджу с Live CD )))))




root@ubuntu:/home/ubuntu# smartctl -a /dev/sda
smartctl version 5.38 [i686-pc-linux-gnu] Copyright (C) 2002-8 Bruce Allen
Home page is http://smartmontools.sourceforge.net/

=== START OF INFORMATION SECTION ===
Device Model: WDC WD1600BEVT-22ZCT0
Serial Number: WD-WXC308691852
Firmware Version: 11.01A11
User Capacity: 160*041*885*696 bytes
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 8
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Fri Jul 2 16:44:52 2010 UTC
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: FAILED!
Drive failure expected in less than 24 hours. SAVE ALL DATA.
See vendor-specific Attribute list for failed Attributes.

General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (5160) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 64) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x303f) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 200 198 051 Pre-fail Always - 1
3 Spin_Up_Time 0x0027 160 159 021 Pre-fail Always - 975
4 Start_Stop_Count 0x0032 097 097 000 Old_age Always - 3001
5 Reallocated_Sector_Ct 0x0033 117 117 140 Pre-fail Always FAILING_NOW 661
7 Seek_Error_Rate 0x002e 100 253 051 Old_age Always - 0
9 Power_On_Hours 0x0032 095 095 000 Old_age Always - 4312
10 Spin_Retry_Count 0x0033 100 099 051 Pre-fail Always - 0
11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 098 098 000 Old_age Always - 2624
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 531
193 Load_Cycle_Count 0x0032 167 167 000 Old_age Always - 101993
194 Temperature_Celsius 0x0022 092 084 000 Old_age Always - 51
196 Reallocated_Event_Count 0x0032 188 188 000 Old_age Always - 12
197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 100 253 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 224
200 Multi_Zone_Error_Rate 0x0009 100 253 051 Pre-fail Offline - 0

SMART Error Log Version: 1
ATA Error Count: 3733 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 3733 occurred at disk power-on lifetime: 4189 hours (174 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 61 06 ff ff ff 00 Device Fault; Error: ABRT

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ef 90 06 ff ff ff 00 00 00:03:36.950 SET FEATURES [Reserved for Serial ATA]
ef 90 06 ff ff ff 00 00 00:03:36.950 SET FEATURES [Reserved for Serial ATA]
ef 10 06 00 00 00 00 00 00:00:20.628 SET FEATURES [Reserved for Serial ATA]
ec 00 00 00 00 00 00 00 00:00:20.626 IDENTIFY DEVICE
ef 03 45 00 00 00 00 00 00:00:20.626 SET FEATURES [Set transfer mode]

Error 3732 occurred at disk power-on lifetime: 4189 hours (174 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 61 06 ff ff ff 00 Device Fault; Error: ABRT

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ef 90 06 ff ff ff 00 00 00:03:36.950 SET FEATURES [Reserved for Serial ATA]
ef 10 06 00 00 00 00 00 00:00:20.628 SET FEATURES [Reserved for Serial ATA]
ec 00 00 00 00 00 00 00 00:00:20.626 IDENTIFY DEVICE
ef 03 45 00 00 00 00 00 00:00:20.626 SET FEATURES [Set transfer mode]
ef 10 06 00 00 00 00 00 00:00:20.626 SET FEATURES [Reserved for Serial ATA]

Error 3731 occurred at disk power-on lifetime: 4189 hours (174 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 61 06 00 00 00 a0 Device Fault; Error: ABRT

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ef 10 06 00 00 00 00 00 00:00:20.628 SET FEATURES [Reserved for Serial ATA]
ec 00 00 00 00 00 00 00 00:00:20.626 IDENTIFY DEVICE
ef 03 45 00 00 00 00 00 00:00:20.626 SET FEATURES [Set transfer mode]
ef 10 06 00 00 00 00 00 00:00:20.626 SET FEATURES [Reserved for Serial ATA]
ec 00 00 00 00 00 00 00 00:00:20.625 IDENTIFY DEVICE

Error 3730 occurred at disk power-on lifetime: 4189 hours (174 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 61 45 00 00 00 a0 Device Fault; Error: ABRT

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ef 03 45 00 00 00 00 00 00:00:20.626 SET FEATURES [Set transfer mode]
ef 10 06 00 00 00 00 00 00:00:20.626 SET FEATURES [Reserved for Serial ATA]
ec 00 00 00 00 00 00 00 00:00:20.625 IDENTIFY DEVICE
ef 10 06 00 00 00 00 00 00:00:15.323 SET FEATURES [Reserved for Serial ATA]
ec 00 00 00 00 00 00 00 00:00:15.321 IDENTIFY DEVICE

Error 3729 occurred at disk power-on lifetime: 4189 hours (174 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 61 06 00 00 00 a0 Device Fault; Error: ABRT

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ef 10 06 00 00 00 00 00 00:00:20.626 SET FEATURES [Reserved for Serial ATA]
ec 00 00 00 00 00 00 00 00:00:20.625 IDENTIFY DEVICE
ef 10 06 00 00 00 00 00 00:00:15.323 SET FEATURES [Reserved for Serial ATA]
ec 00 00 00 00 00 00 00 00:00:15.321 IDENTIFY DEVICE
ef 03 45 00 00 00 00 00 00:00:15.321 SET FEATURES [Set transfer mode]

SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed: unknown failure 90% 4190 -
# 2 Short offline Completed: unknown failure 90% 4189 -
# 3 Conveyance offline Completed: unknown failure 90% 4183 -
# 4 Extended offline Completed: unknown failure 90% 4183 -
# 5 Short offline Completed: unknown failure 90% 4183 -
# 6 Short offline Completed: unknown failure 90% 4145 -

SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.