[maglor]

ссылку создал , kppp у меня нету , а обычный мастер его не видит , linuxconf определил его
еще я что то сделал нечайна , что когда я попробовал подключиться к нету модем начал дозваниваться !!! Правда в тоновом режиме , как его отключить? Я так и не понял что я сделал , а все свои операции произвести не смог((

[Alex AD]

у меня тож трабла с модемом, мандрейк10 его определил как USRobotics 5610 так оно и есть, модем хардовый в альте поставился без проблем и пахал без нареканий, тут папки dev/modem нету, вместо dev/modem ставил dev/ttyS1 или ttyS0, пишет что модем готов, но при инициализации всё останавливается что делать подскажите? при чем модем находится в неизвестных устройствах?! в строке инициализации у меня стоит ATZ, какие ещё можно попробывать строки инициализации? при опросе модема в kppp выдаёт пустые строки, в винде висит на com3

[makaveli lcf]

maglor
а звонилка какая? нужно в строке набора номера вместо
ATDT номер_телефона
написать
ATDP номер_телефона

(T - tone, P - pulse)

[maglor]

звонилку походу звать drakconnect
серавно не фурычит , может это дистрибутив кривой у меня:/

[Alex AD]

вот что выдали у меня dmesg & lspci:

Linux version 2.6.3-4mdk (nplanel@n3.mandrakesoft.com) (gcc version 3.3.2 (Mandrake Linux 10.0 3.3.2-6mdk)) #1 Tue Mar 2 07:26:13 CET 2004
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000ec000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000007ff0000 (usable)
BIOS-e820: 0000000007ff0000 - 0000000007ff8000 (ACPI data)
BIOS-e820: 0000000007ff8000 - 0000000008000000 (ACPI NVS)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
127MB LOWMEM available.
On node 0 totalpages: 32752
 DMA zone: 4096 pages, LIFO batch:1
 Normal zone: 28656 pages, LIFO batch:6
 HighMem zone: 0 pages, LIFO batch:1
DMI 2.3 present.
ACPI: RSDP (v000 AMI                                       ) @ 0x000fa970
ACPI: RSDT (v001 AMIINT VIA_K7   0x00000010 MSFT 0x00000097) @ 0x07ff0000
ACPI: FADT (v001 AMIINT VIA_K7   0x00000011 MSFT 0x00000097) @ 0x07ff0030
 >>> ERROR: Invalid checksum
ACPI: DSDT (v001    VIA   VT8371 0x00001000 MSFT 0x0100000b) @ 0x00000000
ACPI: Unable to map DSDT
ACPI: DSDT not present
ACPI: DSDT not present
ACPI: DSDT not present
ACPI: DSDT not present
ACPI: DSDT not present
ACPI: DSDT not present
ACPI: DSDT not present
ACPI: DSDT not present
Built 1 zonelists
Kernel command line: auto BOOT_IMAGE=linux ro root=305 devfs=mount acpi=ht resume=/dev/hda6 splash=silent
bootsplash: silent mode.
Local APIC disabled by BIOS -- reenabling.
Found and enabled local APIC!
Initializing CPU#0
PID hash table entries: 512 (order 9: 4096 bytes)
Detected 1200.573 MHz processor.
Using tsc for high-res timesource
Console: colour dummy device 80x25
Memory: 125764k/131008k available (1815k kernel code, 4704k reserved, 846k data, 272k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 2359.29 BogoMIPS
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 132k freed
CPU:     After generic identify, caps: 0383fbff c1c3fbff 00000000 00000000
CPU:     After vendor identify, caps: 0383fbff c1c3fbff 00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 64K (64 bytes/line)
CPU:     After all inits, caps: 0383fbff c1c3fbff 00000000 00000020
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: AMD Duron(tm) stepping 01
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 1199.0841 MHz.
..... host bus clock speed is 199.0973 MHz.
NET: Registered protocol family 16
EISA bus registered
PCI: PCI BIOS revision 2.10 entry at 0xfdb31, last bus=1
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20040211
ACPI: Interpreter disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
PnPBIOS: Disabled
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI: Using IRQ router VIA [1106/0686] at 0000:00:07.0
vesafb: framebuffer at 0xd0000000, mapped to 0xc8800000, size 16384k
vesafb: mode is 800x600x16, linelength=1600, pages=3
vesafb: protected mode interface info at c000:c460
vesafb: scrolling: redraw
vesafb: directcolor: size=0:5:6:5, shift=0:11:5:0
fb0: VESA VGA frame buffer device
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
ikconfig 0.7 with /proc/config*
spurious 8259A interrupt: IRQ7.
VFS: Disk quotas dquot_6.5.1
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
Initializing Cryptographic API
Applying VIA southbridge workaround.
PCI: Disabling Via external APIC routing
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
bootsplash 3.1.3-2003/11/14: looking for picture.... silentjpeg size 14856 bytes, found (800x600, 14808 bytes, v3).
Console: switching to colour frame buffer device 92x32
pty: 1024 Unix98 ptys configured
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
PCI: Found IRQ 9 for device 0000:00:0f.0
PCI: Sharing IRQ 9 with 0000:00:07.3
PCI: Sharing IRQ 9 with 0000:00:07.2
ttyS4 at I/O 0xc800 (irq = 9) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 32000K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:07.1
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: VIA vt82c686b (rev 40) IDE UDMA100 controller on pci0000:00:07.1
   ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio
   ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:pio
hda: ST380011A, ATA DISK drive
Using anticipatory io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hdc: RICOH CD-RW MP7320A, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 1024KiB
hda: 156301488 sectors (80026 MB) w/2048KiB Cache, CHS=16383/255/63, UDMA(100)
/dev/ide/host0/bus0/target0/lun0: p1 p2 < p5 p6 p7 p8 >
Console: switching to colour frame buffer device 92x32
mice: PS/2 mouse device common for all mice
serio: i8042 AUX port at 0x60,0x64 irq 12
input: ImExPS/2 Generic Explorer Mouse on isa0060/serio1
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
EISA: Probing bus 0 at eisa0
NET: Registered protocol family 2
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 8192 bind 16384)
NET: Registered protocol family 1
BIOS EDD facility v0.12 2004-Jan-26, 1 devices found
Please report your BIOS at http://linux.dell.com/edd/results.html
Resume Machine: resuming from /dev/hda6
Resuming from device hda6
Resume Machine: This is normal swap space
PM: Reading pmdisk image.
PM: Resume from disk failed.
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
Mounted devfs on /dev
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Mounted devfs on /dev
Freeing unused kernel memory: 272k freed
Real Time Clock Driver v1.12
drivers/usb/core/usb.c: registered new driver usbfs
drivers/usb/core/usb.c: registered new driver hub
drivers/usb/host/uhci-hcd.c: USB Universal Host Controller Interface driver v2.1
PCI: Found IRQ 9 for device 0000:00:07.2
PCI: Sharing IRQ 9 with 0000:00:07.3
PCI: Sharing IRQ 9 with 0000:00:0f.0
uhci_hcd 0000:00:07.2: UHCI Host Controller
uhci_hcd 0000:00:07.2: irq 9, io base 0000cc00
uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
PCI: Found IRQ 9 for device 0000:00:07.3
PCI: Sharing IRQ 9 with 0000:00:07.2
PCI: Sharing IRQ 9 with 0000:00:0f.0
uhci_hcd 0000:00:07.3: UHCI Host Controller
uhci_hcd 0000:00:07.3: irq 9, io base 0000d000
uhci_hcd 0000:00:07.3: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usb 1-2: new full speed USB device using address 2
EXT3 FS on hda5, internal journal
Adding 506008k swap on /dev/hda6.  Priority:-1 extents:1
SCSI subsystem initialized
imm: Version 2.05 (for Linux 2.4.0)
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE]
parport0: cpp_daisy: aa5500ff(38)
parport0: assign_addrs: aa5500ff(38)
parport0: cpp_daisy: aa5500ff(38)
parport0: assign_addrs: aa5500ff(38)
parport_pc: Via 686A parallel port: io=0x378
ppa: Version 2.07 (for Linux 2.4.x)
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected VIA Twister-K/KT133x/KM133 chipset
agpgart: Maximum main memory to use for agp memory: 94M
agpgart: AGP aperture is 64M @ 0xe0000000
kjournald starting.  Commit interval 5 seconds
EXT3 FS on hda8, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Supermount version 2.0.4 for kernel 2.6
kjournald starting.  Commit interval 5 seconds
EXT3 FS on hda7, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
ip_tables: (C) 2000-2002 Netfilter core team
ip_conntrack version 2.1 (1023 buckets, 8184 max) - 300 bytes per conntrack
inserting floppy driver for 2.6.3-4mdk
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
hdc: ATAPI 40X CD-ROM CD-R/RW drive, 8192kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
ide-floppy driver 0.99.newide
drivers/usb/core/usb.c: registered new driver hiddev
drivers/usb/core/usb.c: registered new driver hid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
NET: Registered protocol family 17
PCI: Found IRQ 10 for device 0000:00:07.5
PCI: Setting latency timer of device 0000:00:07.5 to 64
NET: Registered protocol family 10
Disabled Privacy Extensions on device c035fa20(lo)
IPv6 over IPv4 tunneling driver
lp0: using parport0 (polling).
lp0: console ready
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
bootsplash 3.1.3-2003/11/14: looking for picture.... found (800x600, 11943 bytes, v3).
bootsplash: status on console 0 changed to on
bootsplash 3.1.3-2003/11/14: looking for picture.... found (800x600, 11943 bytes, v3).
bootsplash: status on console 1 changed to on
bootsplash 3.1.3-2003/11/14: looking for picture.... found (800x600, 11943 bytes, v3).
bootsplash: status on console 2 changed to on
bootsplash 3.1.3-2003/11/14: looking for picture.... found (800x600, 11943 bytes, v3).
bootsplash: status on console 3 changed to on
bootsplash 3.1.3-2003/11/14: looking for picture.... found (800x600, 11943 bytes, v3).
bootsplash: status on console 4 changed to on
bootsplash 3.1.3-2003/11/14: looking for picture.... found (800x600, 11943 bytes, v3).
bootsplash: status on console 5 changed to on
mtrr: 0xd0000000,0x4000000 overlaps existing 0xd0000000,0x1000000
atkbd.c: Unknown key released (translated set 2, code 0x7a on isa0060/serio0).
atkbd.c: This is an XFree86 bug. It shouldn't access hardware directly.

00:00.0 Host bridge: VIA Technologies, Inc. VT8363/8365 [KT133/KM133] (rev 03)
Subsystem: Giga-byte Technology: Unknown device 0000
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 8
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=64M]
Capabilities: [a0] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:01.0 PCI bridge: VIA Technologies, Inc. VT8363/8365 [KT133/KM133 AGP] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 00009000-00009fff
Memory behind bridge: dde00000-dfefffff
Prefetchable memory behind bridge: cdc00000-ddcfffff
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South] (rev 40)
Subsystem: VIA Technologies, Inc. VT82C686/A PCI to ISA Bridge
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:07.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT8233/A/C/VT8235 PIPC Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP])
Subsystem: VIA Technologies, Inc. VT82C586/B/VT82C686/A/B/VT8233/A/C/VT8235 PIPC Bus Master IDE
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Region 4: I/O ports at ffa0 [size=16]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:07.2 USB Controller: VIA Technologies, Inc. USB (rev 1a) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64, cache line size 08
Interrupt: pin D routed to IRQ 9
Region 4: I/O ports at cc00 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:07.3 USB Controller: VIA Technologies, Inc. USB (rev 1a) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64, cache line size 08
Interrupt: pin D routed to IRQ 9
Region 4: I/O ports at d000 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:07.4 SMBus: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 40)
Subsystem: Giga-byte Technology: Unknown device 0000
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Capabilities: [68] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:07.5 Multimedia audio controller: VIA Technologies, Inc. VT82C686 AC97 Audio Controller (rev 50)
Subsystem: Giga-byte Technology: Unknown device a002
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin C routed to IRQ 10
Region 0: I/O ports at dc00 [size=256]
Region 1: I/O ports at d800 [size=4]
Region 2: I/O ports at d400 [size=4]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:0f.0 Serial controller: 5610 56K FaxModem 56K FaxModem Model 5610 (rev 01) (prog-if 02 [16550])
Subsystem: 5610 56K FaxModem USR 56k Internal Voice Modem (Model 2976)
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 9
Region 0: I/O ports at c800 [size=8]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1- D2+ AuxCurrent=0mA PME(D0+,D1-,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-

01:00.0 VGA compatible controller: nVidia Corporation NV11 [GeForce2 MX/MX 400] (rev b2) (prog-if 00 [VGA])
Subsystem: Asustek Computer, Inc.: Unknown device 403d
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (1250ns min, 250ns max)
Interrupt: pin A routed to IRQ 11
Region 0: Memory at de000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at d0000000 (32-bit, prefetchable) [size=128M]
Expansion ROM at dfef0000 [disabled] [size=64K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [44] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA- ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>

via-agp         : VIA Technologies|VT8363/8365 [KT133/KM133] [BRIDGE_HOST]
unknown         : VIA Technologies|VT8363/8365 [KT133/KM133 AGP] [BRIDGE_PCI]
unknown         : VIA Technologies|VT82C686 [Apollo Super] [BRIDGE_ISA]
unknown         : VIA Technologies|VT82C586 IDE [Apollo] [STORAGE_IDE]
usb-uhci        : VIA Technologies|VT82C586B USB [SERIAL_USB]
usb-uhci        : VIA Technologies|VT82C586B USB [SERIAL_USB]
unknown         : VIA Technologies|VT82C686 [Apollo Super ACPI] [SERIAL_SMBUS]
snd-via82xx     : VIA Technologies|VT82C686 [Apollo Super AC97/Audio] [MULTIMEDIA_AUDIO]
unknown         : US Robotics/3Com|56K FaxModem Model 5610 [COMMUNICATION_SERIAL]
Card:NVIDIA GeForce2 DDR (generic): nVidia Corporation|NV11 Geforce2 MX/MX 400 [DISPLAY_VGA]
unknown         : Linux 2.6.3-4mdk uhci_hcd|UHCI Host Controller [Hub]
unknown         : Linux 2.6.3-4mdk uhci_hcd|UHCI Host Controller [Hub]
scanner         : Canon Inc.|CanoScan N670U

и ёще при настройке модема вылезло вот это:
Undefined subrouting& network ::modem::ppp_read_conf called at /usr/bin/perl-install/network/network.pm line 423
при чём вот этого нет /perl-install/network/network.pm
помогите я уже замучился

У меня тоже U.S.Robotics 56K 3CP2976-OEM PCI, Linux Mandrake 10

Для настройки модема нужно:
1. Убедиться в наличии утилиты setserial (должно быть в дистрибутиве,но у меня почему-то не оказалось,пришлось скачать с ftp мандрайка и установить)
2. Установить драйвер модема под рутом

  rpm -i 3ComMdm-1.0-1.i386.rpm

3. Драйвер установит команду конфигурации порта для модема (с помощью setserial), поэтому дальше просто
вводим эту команду(также под рутом)

  3ComMdm

4. Далее в настройках KPPP устанавливаем

  Устройство модема /dev/modem

5. Можно ещё установить импульсный набор (изменить в командах модема ATDT на ATDP) и отключить
использоание лок  файла.

После этих операций мой модем заработал.

Удачи!

[Alex AD]

у меня устройство модема не /dev/modem, а ttyS3 и тоже всё пашет

[pilgrim2k]

добрый день всем!
я тут решил совершил наверняка необдуманный поступок и перешел с вин на линь...
вообщем все бы ничего, но у меня аналогичная проблема..только модем у меня cxt10b6 HCF PCI.. ошибки те же.. папка dev/modem отсуствует... какой то модем определяется на dev/ttyS1... только виснет тоже на инициализации... все совету тут не помогли... ходил на линуксант... у меня версия ядра 2.6.3-4mdk ... i686 .. rpm вк консоли пишет какой то возврат ошибки 124... и еще он пишет что версия ядра не подходит... кстати это возможно, на линуксанте самое старое это 2.6.11mdr ... но там нет другого... и нигде найти не могу...

а модем определился в списке неизвестных тоже... вообщем все как у Alex AD.

ни у кого не завалялось чего нить мне нужного?