Цитата Ment69:
|
J7BXA, Проверьте настройки биоса касающиеся питания. »
|
Вот, что по этому поводу написано в мануле:
читать дальше »
3-8 Power Management Setup
The Power Management Setup allows you to configure your system to most effectively save
energy saving while operating in a manner consistent with your own style of computer use.
CMOS Setup Utility – Copyright(C) 1984-2002 Award Software
Power Management Setup
ACPI Function Enabled
Item Help
ACPI Suspend Type S1(POS)
Video Off Option Suspend -> off
Video off Method V/H SYNC+Blank
Menu Level >
Video Off In Suspend Yes
MODEM Use IRQ 3
HDD Power Down Disabled
Soft-off by PWR-BTTN Instant-off
Wake-Up by PCI card Disabled
Power On by Ring Disabled
Resume by Alarm Disabled
X Date (of Month) 0
X Time (hh:mm:ss) 0 : 0 :0
CPU Thermal Management Timer 32 Min
DRAM Read Thermal Management Disabled
> PM Timer Reload Events Press Enter
Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
^v><
F5:Previous Values F6:Optimized Defaults F7:Standard Defaults
ACPI Function
This item allows you to Enabled/Disabled the Advanced Configuration and Power Management
(ACPI). The settings are Enabled and Disabled.
ACPI Suspend Type
This item allows you to select ACPI Suspend Type.
The setting are: S1(POS), S3(STR)
Video Off in Suspend
This determines the manner in which the monitor is blanked. The choice are Yes Video
will off , and No Video always On.
Video Off Method
This determines the manner in which the monitor is blanked.
(default) Initial display power management signaling.
DPMS
This option only writes blanks to the video buffer.
Blank Screen
This selection will cause the system to turn off the vertical and
V/H SYNC+Blank
horizontal synchronization ports and write blanks to the video
buffer.
Modem Use IRQ
This determines the IRQ in which the MODEM can use.
The settings are: 3, 4, 5, 7, 9, 10, 11, NA.
Power Button Function
Pressing the power button for more than 4 seconds forces the system to enter the Soft-Off
state. The settings are: Delay 4 Sec, Instant-Off.
Wake-Up by PCI card /Power On by Ring
During Disabled, the system will ignore any incoming call from the PCI card/modem. During
Enabled, the system will boot up if there’s an incoming call from the PCI card /modem.
Wake-Up on RTC Alarm
This function is for setting date and time for your computer to boot up. During Disabled, you
cannot use this function. During Enabled, choose the Date and Time Alarm:
Date(of month) Alarm
You can choose which month the system will boot up. Set to 0, to boot every day.
Time(hh:mm:ss) Alarm
You can choose what hour, minute and second the system will boot up.
Note: If you have change the setting, you must let the system boot up until it goes
to the operating system, before this function will work
PM Timer Reload Events
Please refer to section 3-8-1
3-8-1 PM Timer Reload Events
CMOS Setup Utility – Copyright(C) 1984-2002 Award Software
PM Timer Reload Events
Primary IDE 0 Disabled
Item Help
Primary IDE 1 Disabled
Secondary IDE 0 Disabled
Secondary IDE 1 Disabled
Menu Level >>
FDD, COM, LPT Port Disabled
PCI PIRQ [A-D] # Disabled
Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
^v><
F5:Previous Values F6:Optimized Defaults F7:Standard Defaults
А для тех, кто будет искать мануал на материнки Jetway 845D Pro, 845DDA и 845DDAL специально выкладываю ссылку:
Rapidshare.com
Rapidshare.ru
Depositfiles.com/ru
ifolder.ru