[kim-aa]

Serial0 и Serial1 подключаются к V35. Может быть и к RS232.


Приведите результаты:

sh run
sh ver
sh controllers

Спецификация кабеля
http://www.cisco.com/en/US/products/...801f5d86.shtml

Думаю вам лучше поискать Hub с Ethernet и AUI, а кабель можно и самому спаять

[V.Gutin]

sh ver:

Код:

Cisco Internetwork Operating System Software
IOS (tm) 3000 Bootstrap Software (IGS-BOOT-R), Version 11.0(10c), RELEASE SOFTWA
RE (fc1)
Copyright (c) 1986-1996 by cisco Systems, Inc.
Compiled Fri 27-Dec-96 17:33 by loreilly
Image text-base: 0x01010000, data-base: 0x00001000

ROM: System Bootstrap, Version 11.0(10c), SOFTWARE

Router uptime is 5 minutes
System restarted by power-on
Running default software

cisco 2500 (68030) processor (revision N) with 2048K/2048K bytes of memory.
Processor board ID 06178143, with hardware revision 00000000
X.25 software, Version 2.0, NET2, BFE and GOSIP compliant.
1 Ethernet/IEEE 802.3 interface.
2 Serial network interfaces.
32K bytes of non-volatile configuration memory.
8192K bytes of processor board System flash (Read/Write)

Configuration register is 0x2142

sh controllers:

Код:

                      
LANCE unit 0, idb 0x740D8, ds 0x76008, regaddr = 0x2130000, reset_mask 0x2                                                                          
IB at 0x206E60: mode=0x0000, mcfilter 0000/0000/0000/0000                                                         
station address 00e0.1ea9.5ad9  default station address 00e0.1ea9.5ad9                                                                      
buffer size 1524                
RX ring with 4 entries at 0x206EA0                                  
Rxhead = 0x206EA0 (0), Rxp = 0x76024 (0)                                        
00 pak=0x0765E4 ds=0x207DD6 status=0x80 max_size=1524 pak_size=0                                                                
01 pak=0x07677C ds=0x208492 status=0x80 max_size=1524 pak_size=0                                                                
02 pak=0x076914 ds=0x208B4E status=0x80 max_size=1524 pak_size=0                                                                
03 pak=0x076AAC ds=0x20920A status=0x80 max_size=1524 pak_size=0                                                                
TX ring with 1 entries at 0x206F58, tx_count = 0                                                
tx_head = 0x206F58 (0), head_txp = 0x76078 (0)                                              
tx_tail = 0x206F58 (0), tail_txp = 0x76078 (0)                                              
00 pak=0x000000 ds=0x200072 status=0x4                                    
0 missed datagrams, 0 overruns, 0 late collisions, 1 lost carrier events                                                                        
0 transmitter underruns, 0 excessive collisions,  0 tdr, 0 babbles                                                                  
0 memory errors, 0 spurious initialization done interrupts                                                          
0 no enp status, 0 buffer errors, 0 overflow errors                                                   
0 one_col, 0 more_col, 0 deferred, 0 tx_buff                                            
0 throttled, 0 enabled                      
Lance csr0 = 0x4                
HD unit 0, idb = 0x7C92C, driver structure at 0x80DD0                                                     
buffer size 1524  HD unit 0, No cable                                     
cpb = 0x20, eda = 0xA850, cda = 0xA800                                      
RX ring with 4 entries at 0x20A800                                  
00 bd_ptr=0xA800 pak=0x0812E8 ds=0x20BF5C status=80 pak_size=0                                                              
01 bd_ptr=0xA814 pak=0x081480 ds=0x20C618 status=80 pak_size=0                                                              
02 bd_ptr=0xA828 pak=0x081618 ds=0x20CCD4 status=80 pak_size=0                                                              
03 bd_ptr=0xA83C pak=0x0817B0 ds=0x20D390 status=80 pak_size=0                                                              
04 bd_ptr=0xA850 pak=0x081948 ds=0x20DA4C status=80 pak_size=0                                                              
cpb = 0x20, eda = 0xB000, cda = 0xB000                                      
TX ring with 2 entries at 0x20B000                                  
00 bd_ptr=0xB000 pak=0x000000 ds=0x000000 status=80 pak_size=0                  
01 bd_ptr=0xB014 pak=0x000000 ds=0x000000 status=80 pak_size=0
02 bd_ptr=0xB028 pak=0x000000 ds=0x000000 status=80 pak_size=0
0 missed datagrams, 0 overruns
0 bad datagram encapsulations, 0 memory errors
0 transmitter underruns
HD unit 1, idb = 0x81CB8, driver structure at 0x86158
buffer size 1524  HD unit 1, No cable
cpb = 0x20, eda = 0xE850, cda = 0xE800
RX ring with 4 entries at 0x20E800
00 bd_ptr=0xE800 pak=0x086674 ds=0x20FF5C status=80 pak_size=0
01 bd_ptr=0xE814 pak=0x08680C ds=0x210618 status=80 pak_size=0
02 bd_ptr=0xE828 pak=0x0869A4 ds=0x210CD4 status=80 pak_size=0
03 bd_ptr=0xE83C pak=0x086B3C ds=0x211390 status=80 pak_size=0
04 bd_ptr=0xE850 pak=0x086CD4 ds=0x211A4C status=80 pak_size=0
cpb = 0x20, eda = 0xF000, cda = 0xF000
TX ring with 2 entries at 0x20F000
00 bd_ptr=0xF000 pak=0x000000 ds=0x000000 status=80 pak_size=0
01 bd_ptr=0xF014 pak=0x000000 ds=0x000000 status=80 pak_size=0
02 bd_ptr=0xF028 pak=0x000000 ds=0x000000 status=80 pak_size=0
0 missed datagrams, 0 overruns
0 bad datagram encapsulations, 0 memory errors
0 transmitter underruns

на sh run выдает

Код:

Router(boot)>sh run                   
                 ^                  
% Invalid input detected at '^' marker.                                       

Router(boot)>sh run ?                     
% Unrecognized command

На складе нашелся Compex TP1016c 16-PORT ETHERNET 10BASE-T REPEATER у которого есть AUI но беда в том что у него разъем "мама". Тоесть нужен кабель DB15 "папа"-"папа" а таких, насколько я знаю, в природе нету.

[kim-aa]

1) AUI to AUI можно самому спаять

http://www.hardwarebook.info


2) sh run (и вообще большую часть "низких") команд надо отдавать в режиме супервизора
(о котором говорит приглашение #), т.е.

> ena
# sh run

[V.Gutin]

Сделал

Код:

Router(boot)>ena                
Router(boot)#sh run                   
Building configuration...                         

Current configuration:                      
! 
version 11.0            
service udp-small-servers                         
service tcp-small-servers                         
! 
hostname Router               
! 
! 
! 
interface Ethernet0                   
 no ip ad        
 no ip route-cache                  
 shutdown         
!
interface Serial0
 no ip address
 no ip route-cache
 shutdown
!
interface Serial1
 no ip address
 no ip route-cache
 shutdown
!
!
line con 0
line aux 0
 transport input all
line vty 0 4
 login
!
end
!
!
line con 0
line aux 0
 transport input all
line vty 0 4
 login
!
end

Нашел распиновку http://www.allpinouts.org/index.php/Ethernet_AUI_to_AUI остается непонятным строка:
And make the following jumper at each end